Just How to Install a Bathtub Yourself
Just How to Install a Bathtub Yourself
Blog Article
How do you feel in regards to Tools You Need to Install a New Bathtub ?
Mounting a tub isn't precisely rocket science, but it does call for strong plumbing, carpentry, and sometimes, tiling abilities. Changing an old bathtub with a new one is also a moderately hard task. If the old tub is readily accessible, the task can move quickly; if you need to open up a wall to remove the old bathtub as well as position the brand-new tub, the task is a lot harder. In either situation, the project is within a house handyman's skills, although you will certainly need a helper to vacate the old tub and embeded in the new one. See to it you have actually qualified on your own for the task and also fit trying it. Rather than working with a contractor to take control of a halfway-completed job, it is far better to think about using one prior to you begin. Opportunities are you may require a professional plumber to make tube links.
This short article will certainly assist you mount a new bath tub in your restroom if you have actually already acquired a new bathtub and do not need to alter the arrangement of your previous water system pipes.
Your devices and also material list ought to consist of the following:
Removing Old Touches
If you need to change old taps with new ones as a part of your installment, then the first thing you must do is separate the supply of water. After doing so, activate the taps to drain any type of water continuing to be in the system. The process of eliminating the existing faucets can be quite troublesome as a result of the restricted gain access to that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a fabric all set for the remaining water that will certainly come from the pipes. As soon as the supply pipelines have been eliminated, utilize the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from turning throughout this process. When the faucets have actually been removed, the holes in the bath/basin will have to be cleaned up of any kind of old securing compound.
Before proceeding to fit the new taps, contrast the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a link to the existing supply pipes.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the placing hole in the bath/basin guaranteeing that the washers are in area in between the tap and the sink. Secure the faucet in position with the producer offered backnut. Once the faucet is safely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical tap connectors. The previous kind ought to be connected to the tap finishes initially, tightening only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Setting up the Bathtub
Making use of both wood boards under its feet, put the bathtub in the required setting. The wooden boards are practical in evenly spreading out the weight of the bathtub over the location of the boards instead of concentrating all the weight onto four little points.
The following objective is to guarantee that the tub is leveled all round. This can be attained by inspecting the level and readjusting the feet on the bathtub up until the level checks out degree.
To mount taps, fit all-time low of the furthest adaptable tap adapter to the suitable supply pipeline by making a compression join; after that do the exact same for the various other tap.
Activate the water supply as well as check all joints as well as new pipework for leaks and also tighten them if required. Load the tub as well as also examine the overflow outlet as well as the regular outlet for leakages.
Finally, take care of the bath paneling as explained in the supplier's instruction manual. Tiling and also sealing around the tub needs to wait until the tub has actually been made use of at least when as this will certainly settle it right into its last position.
Getting ready for the Installment
Firstly, the sustaining structure supplied with the bathroom needs to be fitted (if required) according to the maker's guidelines. Next, fit the taps or mixer to the tub. When suitable the tap block, it is essential to make certain that if the faucet comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bath, it is additionally practical to fit a sustaining plate under the faucets unit to prevent stress on the tub.
Fit the adaptable faucet connectors to the bottom of the two faucets making use of 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you utilize all of the supplied washers.
Link the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final position.
Tiling Around the Bathtub
In the area where the bath fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to crack an inflexible seal, creating the water to pass through the wall surface in between the bath and the tiling, leading to complications with wetness and also feasible leakages to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your fixtures and fittings. They are marketed in tubes and also cartridges, as well as are capable of sealing voids approximately a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of soaked paper or soft rope. Keep in mind to always fill the bath tub with water prior to sealing, to allow for the activity experienced when the bathtub is in usage. The sealant can crack fairly very early if you do not think about this activity prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally quickly offered on the market. It is suggested to fit the floor tiles utilizing water-resistant or waterproof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm very drawn to How to Install a Bathtub and I am hoping you liked the new blog posting. Liked our blog posting? Please share it. Let someone else discover it. We recognize the value of reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Schedule Today
Report this page